Úgy néz ki, jó tartalék lesz. Remélem, a belső bevonat kitart. Azon kívül, hogy úgy néz ki, jól meg van csinálva.

looks like it'll do as a good backup. here's hoping the inner coating will hold up. other than that it looks well made.

Úgy néz ki, jó tartalék lesz. Remélem, a belső bevonat kitart. Azon kívül, hogy úgy néz ki, jól meg van csinálva.

arrivé à temps, fonctionne bien

arrivé à temps, fonctionne bien

arrivé à temps, fonctionne bien

Bought this as a spare part for an Ender 3 Pro. Fits well, but slightly lower quality than stock hot end. Note that it is with the older type heat block (different product pictures), so it can be a bit tricky fitting the glass thermistor correctly to get precise temperature measurements. It is not a problem for me, though, as I already have a newer type heat block, which I intend to use. It can be done, but larger encapsulated thermistors would be better suited for this. Price is slightly high considering the quality and the type of heat block.

Bought this as a spare part for an Ender 3 Pro. Fits well, but slightly lower quality than stock hot end. Note that it is with the older type heat block (different product pictures), so it can be a bit tricky fitting the glass thermistor correctly to get precise temperature measurements. It is not a problem for me, though, as I already have a newer type heat block, which I intend to use. It can be done, but larger encapsulated thermistors would be better suited for this. Price is slightly high considering the quality and the type of heat block.

Bought this as a spare part for an Ender 3 Pro. Fits well, but slightly lower quality than stock hot end. Note that it is with the older type heat block (different product pictures), so it can be a bit tricky fitting the glass thermistor correctly to get precise temperature measurements. It is not a problem for me, though, as I already have a newer type heat block, which I intend to use. It can be done, but larger encapsulated thermistors would be better suited for this. Price is slightly high considering the quality and the type of heat block.

epico salu2 de Bolivia

epico salu2 de Bolivia

epico salu2 de Bolivia

O boy does this thing look pretty, but like a crazy girlfriend they can look really nice, just remember you have to live with them. I can't even say $7 is worth it, I would rather burn the money in a fire pit, I have spent way more than what I saved, in time, trying to get this thing to work right. and that is after waiting 1.5 months to get it. 1. This is not an all metal hot end. There is a ptfe tube in it, that doesn't even line up right. If you want a crash course in how to unclog a hot end, boy golly buy this thing, youll be an expert by then tenth time you do it. 2. The glass thermistor comes in a plastic bag, that's shipped in a paper parcel. Mine didn't make the trip. and was broken on arrival the usual -14 temperature symbol on the ender 3 announced this luckily before I ran the line through the jacket. No big I have another one. 3. The brass nozzle one this "all metal hot end" is short. SHORT. so if you have an upgraded or printed carriage I hope it doesn't rely on a standard length nozzle. 4. This leaky SOB will put pla above and below the hot end. make sure you tighten the "all metal" ptfe tube holder tightly to the block, even then you may get a nice batch of goo on the top of the block. 5. The J connector is not the standard one for ender 3, youll either ahve to unclip the current one and unpin it. or jam the individual pins into your board, i recommend the former. I can't believe I am complaining about a chinese hot end, cause I knew what I was getting into. Do not buy this, I would rather take a chance on some Wish shoes, than do this again. What a total piece of caca. if you do decide to run this gauntlet look up some videos on how to properly place a thermistor before you put this one in if you haven't before, God Speed.

O boy does this thing look pretty, but like a crazy girlfriend they can look really nice, just remember you have to live with them. I can't even say $7 is worth it, I would rather burn the money in a fire pit, I have spent way more than what I saved, in time, trying to get this thing to work right. and that is after waiting 1.5 months to get it. 1. This is not an all metal hot end. There is a ptfe tube in it, that doesn't even line up right. If you want a crash course in how to unclog a hot end, boy golly buy this thing, youll be an expert by then tenth time you do it. 2. The glass thermistor comes in a plastic bag, that's shipped in a paper parcel. Mine didn't make the trip. and was broken on arrival the usual -14 temperature symbol on the ender 3 announced this luckily before I ran the line through the jacket. No big I have another one. 3. The brass nozzle one this "all metal hot end" is short. SHORT. so if you have an upgraded or printed carriage I hope it doesn't rely on a standard length nozzle. 4. This leaky SOB will put pla above and below the hot end. make sure you tighten the "all metal" ptfe tube holder tightly to the block, even then you may get a nice batch of goo on the top of the block. 5. The J connector is not the standard one for ender 3, youll either ahve to unclip the current one and unpin it. or jam the individual pins into your board, i recommend the former. I can't believe I am complaining about a chinese hot end, cause I knew what I was getting into. Do not buy this, I would rather take a chance on some Wish shoes, than do this again. What a total piece of caca. if you do decide to run this gauntlet look up some videos on how to properly place a thermistor before you put this one in if you haven't before, God Speed.

O boy does this thing look pretty, but like a crazy girlfriend they can look really nice, just remember you have to live with them. I can't even say $7 is worth it, I would rather burn the money in a fire pit, I have spent way more than what I saved, in time, trying to get this thing to work right. and that is after waiting 1.5 months to get it. 1. This is not an all metal hot end. There is a ptfe tube in it, that doesn't even line up right. If you want a crash course in how to unclog a hot end, boy golly buy this thing, youll be an expert by then tenth time you do it. 2. The glass thermistor comes in a plastic bag, that's shipped in a paper parcel. Mine didn't make the trip. and was broken on arrival the usual -14 temperature symbol on the ender 3 announced this luckily before I ran the line through the jacket. No big I have another one. 3. The brass nozzle one this "all metal hot end" is short. SHORT. so if you have an upgraded or printed carriage I hope it doesn't rely on a standard length nozzle. 4. This leaky SOB will put pla above and below the hot end. make sure you tighten the "all metal" ptfe tube holder tightly to the block, even then you may get a nice batch of goo on the top of the block. 5. The J connector is not the standard one for ender 3, youll either ahve to unclip the current one and unpin it. or jam the individual pins into your board, i recommend the former. I can't believe I am complaining about a chinese hot end, cause I knew what I was getting into. Do not buy this, I would rather take a chance on some Wish shoes, than do this again. What a total piece of caca. if you do decide to run this gauntlet look up some videos on how to properly place a thermistor before you put this one in if you haven't before, God Speed.

all good as advertised. Thanks.

all good as advertised. Thanks.

all good as advertised. Thanks.

I solved leaking problem of my cr10s with this. Now I am ordering new 0.8-1-1.2 nozzle

I solved leaking problem of my cr10s with this. Now I am ordering new 0.8-1-1.2 nozzle

I solved leaking problem of my cr10s with this. Now I am ordering new 0.8-1-1.2 nozzle

Excellent quality build , have not tried printing with it yet as my extruder at this time is working very well.

Excellent quality build , have not tried printing with it yet as my extruder at this time is working very well.

Excellent quality build , have not tried printing with it yet as my extruder at this time is working very well.

Jól néz ki. Még nem teszteltem, mivel a tartalékok miatt van. Szeretem, hogy vannak csavarok, hogy rögzítse a fűtőbetét és a termisztor, és hogy ezek lehet szerelni balról vagy jobbról.

It look fine. I have not tested it, as it is for emergency spares. I do like that there are grub screws to secure the heater cartridge and the thermistor, and that these can be fitted from the left or the right.

Jól néz ki. Még nem teszteltem, mivel a tartalékok miatt van. Szeretem, hogy vannak csavarok, hogy rögzítse a fűtőbetét és a termisztor, és hogy ezek lehet szerelni balról vagy jobbról.

super

super

super